Skip to main content

Spa Parts Made Simple

Pumps, heaters, control boards, and replacement parts — without the confusion.

Shop Spa Parts
✔️ Real OEM & compatible spa parts
✔️ Fast shipping from the USA
✔️ Knowledgeable support when you need it
✔️ Trusted by spa owners since 2015

Not sure which part fits your spa?

We help you compare possible replacement parts using your model, part number and measurements.

  1. Find your spa model
  2. Match the part number
  3. Order with confidence
Get Help Finding a Part

SpaShopper makes it easy to find quality hot tub and spa replacement parts without the frustration. From spa pumps and heaters to control boards, jets, filters, and plumbing components, we stock parts that fit a wide range of popular spa brands. Whether you’re fixing a heating issue, replacing a worn pump, or upgrading aging components, SpaShopper helps you get your spa running again quickly and confidently.

Find Your Watkins Pump Parts With Two Numbers, Then Rebuild It

Find Your Watkins Pump Parts With Two Numbers, Then Rebuild It

Posted by Spa Shopper on Nov 17th 2026

Find Your Watkins Pump Parts With Two Numbers, Then Rebuild It

The quick answer: two numbers on the pump label

If you own a Hot Spring, Caldera, Tiger River, Hotspot or Solana tub, your pump probably needs parts at some point. Finding the right ones is where most people get stuck.

Here is the short version from The Spa Guy. Read the pump model number and the vendor code off the label. In the video the model number is 36675 and the vendor code is 4081. A vendor code of 4081 means an Aquaflow pump.

Get the vendor code right. He says it changes everything, and the wrong one will cause you a problem. Put both numbers in a parts search and it pulls up parts for that exact pump.

What the full rebuild looks like, start to finish

The Spa Guy points out that Watkins does not make pumps. The tub brands buy pumps and put their own stickers on them. That is why the vendor code matters: it tells you who actually made the pump.

His example is a Hot Spring Prodigy with a leaking pump. The shaft looked badly damaged and the pump would not turn. The heater had to come out first, because he says you cannot get the pump out with the heater in place. He took a photo of the wiring before touching anything, and recommends you do the same.

To get the pump apart, he marked the plates so they would line up again. Then he removed the four through bolts and tapped the back cover off with a punch and a screwdriver. He pulled the rotor and clamped it in a vise with a rag around it. Oil filter pliers on the impeller got it loose.

The shaft had swollen so much that the sleeve on the impeller was stuck inside the seal. He broke the ceramic seal piece out (wear safety glasses) and cleaned the shaft with pliers and a wire brush. The motor sounded good when he ran it on a wall plug he made up, so he kept it. The front bearing turned easily, so it did not need replacing.

He entered the model number and vendor code and found three options: a complete wet end, a seal kit with an impeller and a bearing, and a seal kit with an impeller and a seal. The impeller and seal kit was the one this repair needed.

For the seal, he put a tiny bit of silicone on the shaft as a lubricant and pushed the seal on. He did the same inside the ceramic part. Then he reassembled the pump, matching his marks and making sure the wave washer was in place. He tightened the through bolts only snug, threaded the impeller on, and put the eight face screws in with a new O-ring.

He also replaced the O-rings on both unions before the pump went back in. After reinstalling the pump and heater, it ran and held water. The heater came on, but the top side showed locked and the screen acted strangely. He suspected the top side was bad and said he would work on that separately.

Who is behind this store

Spa Shopper is owned and run by The Spa Guy team, the same people who make these videos. The advice you see on camera comes from the people behind the store.

What you get from doing it this way

  • You can identify your exact pump from the label before you order anything.
  • You can choose the right kind of kit: seal and impeller, impeller and bearings, a complete wet end, or a whole pump.
  • A seized pump may still be repairable, as this one was, so you may not need to replace the whole thing.
  • Marking the plates and taking a wiring photo makes reassembly much easier.
  • Replacing the union O-rings while the pump is out helps you avoid a leak when the water comes back on.

Get your numbers, then get your parts

Check your pump label and write down the model number and the vendor code. Then shop Spa Shopper for the kit or parts you need. Search the parts below to get started.

If you cannot find what you need, The Spa Guy says in the video to contact his team and they will see if they can figure it out. Watch the full video to see each step, including the tricky seized-shaft part, before you pick up a wrench.

Shop Spa Shopper

Watch the full video on YouTube